High and Low Temperature (Humidity) Fast Change Rate Chamber

• Customization: Available
• After-sales Service: After-Sales Service Available
• Power Supply: 380 V ± 10% 50Hz 3/N/PE
• Model NO.: JT/JC(CL)-ES Series
• Warranty: 1 Year
• Temperature Range: -70c-+150ºC
• Temperature Fluctuation: ±0.5ºC
• Temperature Deviation: ±2ºC
• Temperature Uniformity: 2ºC
• Transport Package: Wooden Package
• Specification: 250/500/1000/2000 L
• Trademark: JUPITER
• Origin: China
• HS Code: 8479899990

Product Description

Product Description

Introduction
Rapid temperature change test chamber is suitable for electronic components, automotive parts and other materials, such as safety performance testing to provide reliability tests, product screening tests, etc., while the test through this equipment can improve the reliability of the product and the quality control of the product. When the material constituting the various components of the product thermal match is poor, or components of the internal stress is greater, the temperature cycle test can trigger the product by the mechanical structure of the defects of the deterioration of the failure of the product.

Safety & Protections
Power supply undervoltage, over-voltage, missing phase, phase sequence error protection; 3 kinds of overtemperature protection; Heater short circuit protection; Compressor overpressure/ overload/ lack of oil protection; Humidifier fault protection; Blower motor overload/overheat protection; Panel over-current protection, earth leakage protection; cooling water shortage protection.

Application
It is used for electronics, electrical products and machine parts to do cold-resistant test, rapid changes in temperature or gradient test and especially used for electronics, electrical products to do environmental stress screening test.

Options

1. Specialcable port, special shelf;
2. No humidity function(CH*TCES);
3. Dry air purge system;
4. Liquid nitrogen function.

Product Parameters

Parameters for all models 

High-Low Temperature(Humidity) Fast Change Rate Chamber
Model		JT/JC250(CL)-5ES	JT/JC500(CL)-5ES	JT/JC1000(CL)-5ES	JT/JC2000(CL)-5ES
		JT/JC250(CL)-10ES	JT/JC500(CL)-10ES	JT/JC1000(CL)-10ES	JT/JC2000(CL)-10ES
		JT/JC250(CL)-15ES	JT/JC500(CL)-15ES	JT/JC1000(CL)-15ES	JT/JC2000(CL)-15ES
		JT/JC250(CL)-20ES	JT/JC500(CL)-20ES	JT/JC1000(CL)-20ES	JT/JC2000(CL)-20ES
		JT/JC250(CL)-25ES	JT/JC500(CL)-25ES	JT/JC1000(CL)-25ES	JT/JC2000(CL)-25ES
Nominal inside volume(L)		250 L	500 L	1000 L	2000 L
Performance	Temperature range	-70ºC~+150ºC
	Humidity range	20%~98%R.H. (Humidity working range+20ºC~+85ºC, please refer to the temperature and humidity range diagram for details)
	Temperature fluctuation	≤±0.5ºC
	Temperature uniformity	≤2ºC
	Temperature deviation	≤±2ºC
	Humidity deviation	-3~+2%R.H.(75%R.H.above), ±5%R.H.(75%R.H.below)
	Heating rate (Average/ linear, -55~+85ºC)	5ºC/min;10ºC/min;15ºC/min;20ºC/min;25ºC/min
	Cooling rate (Average/ linear, -55~+85ºC)
	Remarks	Above indicators are measured in no load at ambient temperature of 20±2°C(According to GB/T 5170.2-2017)
Internal dimension (mm)D*W*H	5ES	500*700*750	700*850*850	1000*1000*1000	1400*1200*1200
	10/15ES	500*700(/750)*750	700*850*850	900*1150*1000	1100*1400*1300
	20ES	450*750*750	600″850*850	800*1150*1000	1000*1400*1300
	25ES	450*750*750	600*850*850	800*1150*1000	1000*1400*1300
External dimension (mm)D*W*H	5ES	1800*950*1800	1850*1100*1900	2100*1250*2100	2500*1450*2400
	10ES	1800*950*1800	2200*1100*2100	2300*1400*2500	3000*1550*2100
	15ES	2200*1000*2100	2500*1450*2350	2700*1400*2600	3500*1950*2100
	20ES	2200*1000*2100	25001450*2350	2700*1400*2600	3500*1950*2100
	25ES	2300*1000*2100	2600*1450*2350	2900*1400*2600	4000*1950*2100
Caster		4 -6 casters
Inspection window		450*450 Equipped with heating device to prevent condensation and frost formation
Test hole		1 Φ100		2Φ100
Stainless steel shelf (2 pcs in standard		Bearing 25kg/pc		Bearing 50kg/pc
configuration)
Using environment temperature		0~40ºC
Shell		Sprayed steel plate
Interior		SUS304 stainless steel
Cooling mode		water-cooling, (water temperature 7~28ºC,hydraulic pressure 0.2~0.5Mpa,To ensure cooling performance)
Controller		7′ Color touch screen Controller
Communication function		RS485 or standard RJ45 network interface, standard USB interface
Power supply		380V+10%/ 50HZ+1,three-phase-five-wire system (3P+N+G)
Meet the testing method		GB2423.1-2008,GB2423.2-2008,GB2423.3-2008; GB2423.4-2008,GJB150.3-2009,GJB150.4-2009,GJB150.9-2009
Safety precautions		Power supply undervoltage, overvoltage, phase loss, and phase sequence error protection; Triple over temperature protection; Short circuit protection for heaters, Refrigerator overpressure/ overload/ oil shortage protection; Humidifier fault protection; Overload/ overheating protection for blower motor; Control board overcurrent protection, leakage protection; Cooling water shortage protection, etc.
Optional		1. Optional special test holes and special shelves;
		2. Can remove the wet and hot function (model JT * CES);
		3. Optional Dry air blowing system;
		4. Optional liquid nitrogen function.

Centralized control

 

Certifications

Company Profile

Other Products

Cooperation Cases

Packaging & Shipping